1. No power supply
Reason: the printer did not open the power supply; If press the emergency stop button; The power switch damage; The input voltage is too low.
The solution: open the power switch; On both sides of the emergency stop button; Try to press the power switch again; Using the multimeter, measure the actual input voltage, check whether it is normal.
2. Printer printhead is not clear
Reason: there is air in ink tube; Secondary cartridges has no ink; Negative pressure is too large; Data row line not correctly connected to the control panel; Bad printhead control panel; Bad power panel, amplitude set has problem; Poor printhead.
Solution: with long tube suck out ink, then remove the air with a syringe; Check whether there is level 2nd cartridges and liquid level sensor; To properly connected data row line; Replace the printhead control panel; Replace the power supply board; Check the amplitude set, confirmation screen channel so is no problem; Replace the new printhead.
3. Print no ink
Reason: the printhead dirty; There is air in ink tube; Bad printhead; There is too much negative pressure.
Solution: with automatic cleaning system cleaning printhead; With long tube suck out ink, then remove the air with a syringe; Replace the printhead; To recalibrate the negative pressure.
4. Do not meet the correct pressure
Reason: the box to protect the printer ink cartridges (secondary) filling the ink; Negative pressure ink cartridge has the ink; Pressure gauge bad; Refill tube with a hole. Bad air regulator.
The solution: to remove ink from protective box; Remove negative pressure inside the ink; Replace the pressure gauge; Check whether all the refill tube with a hole; Replace the air regulator.
5. The UV lamp is not open
Reason: the UV lamp is bad; The UV lamp switch fault; The UV lamp on and off between the time is too short; The power cord not connected well.
Solution: replace the UV lamp; Check whether there is the UV lamp fault; When the UV lights off, before open again there will be 3-5 minutes of waiting time; This is a circuit protection; All the power cord and check the printer，The UV lamp systems are connected well.
6. Printer configuration of shutter switch properly
Reason: printhead panel bad; Shutter switch does not start on the computer; Shutter configuration is bad
Solution: replace the printhead control panel; Check the Settings on the computer; Determine the UV lamp control has been launched; Change the shutter configuration.
7. Ink control includes sound
Reason: Don’t have enough in ink cartridges.
Solution: check the level of ink cartridges and inject enough.
8. Printer tank to quote
Reason: printhead heating system does not have enough water cycle.
solution: fill in the tank.
9. Printhead (carriage) met in the process of print media
Reason: the distance between the Printhead (carriage) and medium too close; Vacuum pump shut; Vacuum tube set does not match with the media.
Solution: to adjust the printer Printhead (carriage) and the distance between the medium to the 1.0-2.0 mm; Open the vacuum pump switch; For each medium choice adjust vacuum tube to 25%, 50%
, 75% and 100%.
10. In the process of operation, Printhead (carriage) suddenly stopped
Reason: the grating feet dirty; A part of the grating ruler is serious scratch; Bad grating ruler; Bad grating encoder; Grating encoder not installed correctly.
The solution: clean with alcohol grating ruler; Change the print grating ruler; Replace the bad grating ruler; Replacement of grating encoder; Rearrange the grating encoder.
11. The Printhead (carriage) does not move
Reason: the machine offline; servo motor offline.
The solution: press the green switch connected computers and printers; Turn off the machine, restart the reset motor after 10 seconds.
12. The printer automatic cleaning function does not work
Reason: the poor scraping panel; Software failure.
Solution: replace the bad scraping panel; Reinstall the print driver.
13. The printer did not sprayed white ink
Reason: in the options TAB in the dialog on the computer, white ink set in the position of “none”; The nozzle tube in air; To use white ink loop switch before printing.
Solution: check the options TAB in the dialog box white ink on the computer setting is correct; Through the long work syringe to remove air; 5-10 before printing, open loop switch white ink and make one
Level cycle and secondary white ink cartridges.
14. The ink is not dry
Reason: the UV lamp mode setting is not correct; The UV lamp brightness is not enough; The UV lamp is broken; The shutter lamp did not open.
Solution: check the UV lamp mode; According to the “high” key to strengthen the brightness of the UV lamp; Replace the damaged the UV lamp; Check the shutter lamp, to ensure that the shutter lights can work normally.
15. A printer to print a thief
Reason: the printhead arrangement is not correct; Print driver update; The parameters in the wrong color dialog.
The solution: to accurately arranged printhead; Install the latest print driver; Check the color parameters dialog box, to ensure correct Settings.
16. printhead control panel without electricity
Reason: poor printhead control panel; There is no electricity J18 connector.
Solution: replace the printhead control panel; Check + 41 v and + 24 v power supply, ensure the power supply is normal.
17. Flying ink printer output sample
Reason: due to the different media and the electrostatic; Ion fan is turned off.
Solution: make ion fan on the medium for a few seconds to suppress electrostatic generation; Keep the ion fan has been open.